Boring and Profiling  |
| Insert | 105 |
 |
|||
| Bore Ø from |
4.0 mm |
||||
 R = right hand version shown L = left hand version |
for Toolholder Type H105 HC105 B105 VDI B105C B105TS IR105 962 AIH 963 N  |
||||
| Part number | r | f | a | d | b | l2 | l5 | tmax | Dmin |  |
 |
|
| R/L105.1819.1.HV4 | 0.2 | 1.9 | 3.7 | 2.9 | 7 | 10 | 25 | 0.3 | 4.0 | △/△ | ▲/△ | |
| R/L105.1819.2.HV4 | 0.2 | 1.9 | 3.7 | 2.9 | 7 | 15 | 30 | 0.3 | 4.0 | △/△ | ▲/△ | |
| R/L105.1819.3.HV4 | 0.2 | 1.9 | 3.7 | 2.9 | 7 | 20 | 35 | 0.3 | 4.0 | △/△ | ▲/△ | |
| R/L105.1823.1.HV5 | 0.2 | 2.3 | 4.7 | 4.0 | 7 | 10 | 25 | 0.5 | 5.0 | △/△ | ▲/▲ | |
| R/L105.1823.2.HV5 | 0.2 | 2.3 | 4.7 | 4.0 | 7 | 15 | 30 | 0.5 | 5.0 | △/△ | ▲/▲ | |
| R/L105.1823.3.HV5 | 0.2 | 2.3 | 4.7 | 4.0 | 7 | 20 | 35 | 0.5 | 5.0 | △/△ | ▲/▲ | |
| R/L105.1823.4.HV5 | 0.2 | 2.3 | 4.7 | 4.0 | 7 | 25 | 40 | 0.5 | 5.0 | △/△ | ▲/△ | |
| R/L105.1823.5.HV5 | 0.2 | 2.3 | 4.7 | 4.0 | 7 | 30 | 45 | 0.5 | 5.0 | △/△ | ▲/△ | |
| R/L105.1833.2.HV6 | 0.2 | 3.3 | 5.7 | 4.7 | 7 | 15 | 30 | 0.5 | 6.0 | △/△ | ▲/▲ | |
| R/L105.1833.3.HV6 | 0.2 | 3.3 | 5.7 | 4.7 | 7 | 20 | 35 | 0.5 | 6.0 | △/△ | ▲/▲ | |
| R/L105.1833.4.HV6 | 0.2 | 3.3 | 5.7 | 4.7 | 7 | 25 | 40 | 0.5 | 6.0 | △/△ | ▲/△ | |
| R/L105.1833.5.HV6 | 0.2 | 3.3 | 5.7 | 4.7 | 7 | 30 | 45 | 0.5 | 6.0 | △/△ | ▲/△ | |
| R/L105.1840.2.HV7 | 0.2 | 4.0 | 6.4 | 5.2 | 7 | 15 | 30 | 0.5 | 6.8 | △/△ | ▲/▲ | |
| R/L105.1840.3.HV7 | 0.2 | 4.0 | 6.4 | 5.2 | 7 | 20 | 35 | 0.5 | 6.8 | △/△ | ▲/△ | |
| R/L105.1840.4.HV7 | 0.2 | 4.0 | 6.4 | 5.2 | 7 | 25 | 40 | 0.5 | 6.8 | △/△ | ▲/△ | |
| R/L105.1840.5.HV7 | 0.2 | 4.0 | 6.4 | 5.2 | 7 | 30 | 45 | 0.5 | 6.8 | △/△ | ▲/△ | |
| State R or L version | Further sizes upon request Dimensions in mm | P | ||||||||||
| ▲ on stock △ 4 weeks upon request | M | |||||||||||
| recommended |  uncoated grades |
K | ||||||||||
| alternative recommendation |  coated grades |
N | ||||||||||
| not suitable |  brazed / Cermet |
S | ||||||||||
| H | ||||||||||||
| Carbide grades | ||||||||||||
 |
|
 |