Boring and Profiling  |
| Insert | 105 reinforced version |
 |
|||
| Bore Ø from |
5.0 mm |
||||
 R = right hand version shown L = left hand version |
for Toolholder Type H105 HC105 B105 VDI B105C B105TS IR105 962 AIH 963 N |
||||
| Part number | r | f | a | d | b | l2 | l5 | tmax | Dmin |  |
 |
|
| R/L105.1023.005.1.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 10 | 25 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.005.2.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 15 | 30 | 0.15 | 5 | △/△ | ▲/△ | |
| R/L105.1023.005.3.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 20 | 35 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.005.4.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 25 | 40 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.005.5.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 30 | 45 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.005.6.5 | 0.05 | 2.8 | 4.7 | 4.4 | 7 | 35 | 50 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.1.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 10 | 25 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.2.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 15 | 30 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.3.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 20 | 35 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.4.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 25 | 40 | 0.15 | 5 | △/△ | ▲/▲ | |
| R/L105.1023.5.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 30 | 45 | 0.15 | 5 | △/△ | ▲/△ | |
| R/L105.1023.6.5 | 0.20 | 2.8 | 4.7 | 4.4 | 7 | 35 | 50 | 0.15 | 5 | △/△ | ▲/▲ | |
| State R or L version | Further sizes upon request Dimensions in mm | P | ||||||||||
| ▲ on stock △ 4 weeks upon request | M | |||||||||||
| recommended |  uncoated grades |
K | ||||||||||
| alternative recommendation |  coated grades |
N | ||||||||||
| not suitable |  brazed / Cermet |
S | ||||||||||
| H | ||||||||||||
| Carbide grades | ||||||||||||
 |
|
 |