| 30-2181 | 30-2261 | 30-2341 | 30-2421 | 30-2501 | 30-2580 | 30-2660 | 30-2740 |
| 30-2221 | 30-2301 | 30-2381 | 30-2461 | 30-2541 | 30-2620 | 30-2700 |
 |
| HAM 30-2181 solid carbide deep hole drill 5 X D |
|
Engineering data
• Ø d1 0.8–1.45 mm, liquid boost design • special 4-facet ground • special point ground • special chip flute geometry • 30° RH helix |
 |
| Material |  |
 |
 |
 |
 |
 |
 |
 |
 |
 |
|||
| 30-2181 | |||||||||||||
| very suitable | limited suitable | ||||||||||||
 cutting materialsolid carbide ultra micro grain |
 number of teeth - 2 |
 helix angle30° right hand fluted |
 HAM Standard |
 5 x Diameter |
 HAM Standard |
 Point angle 135° |
 Cylindrical Shank |
 Special-polishing process |
 Interior Coolant |
 High Performance Cutting |
 Shrink Fit |
 Liquid Boost |
| Ø d1 (h7) mm |
l3 mm |
l2 mm |
l1 mm |
Ø d2 (h6) mm |
Ø d1 (h7) mm |
l3 mm |
l2 mm |
l1 mm |
Ø d2 (h6) mm |
|
| 0.8 | 4 | 5.5 | 50 | 3 | 1.9 | 9.5 | 12.4 | 55 | 3 | |
| 0.85 | 4.25 | 5.8 | 50 | 3 | 1.95 | 9.8 | 12.7 | 55 | 3 | |
| 0.9 | 4.5 | 6 | 50 | 3 | 2 | 10 | 13 | 55 | 3 | |
| 0.95 | 4.75 | 6.2 | 50 | 3 | 2.05 | 10.3 | 13.3 | 55 | 3 | |
| 1 | 5 | 6.5 | 50 | 3 | 2.1 | 10.5 | 13.7 | 55 | 3 | |
| 1.05 | 5.3 | 6.8 | 50 | 3 | 2.15 | 10.8 | 14 | 55 | 3 | |
| 1.1 | 5.5 | 7.2 | 50 | 3 | 2.2 | 11 | 14.3 | 55 | 3 | |
| 1.15 | 5.8 | 7.5 | 50 | 3 | 2.25 | 11.3 | 14.6 | 55 | 3 | |
| 1.2 | 6 | 7.8 | 50 | 3 | 2.3 | 11.5 | 15 | 55 | 3 | |
| 1.25 | 6.3 | 8.1 | 50 | 3 | 2.35 | 11.8 | 15.3 | 55 | 3 | |
| 1.3 | 6.5 | 8.5 | 50 | 3 | 2.4 | 12 | 15.6 | 55 | 3 | |
| 1.35 | 6.8 | 8.8 | 50 | 3 | 2.45 | 12.3 | 15.9 | 55 | 3 | |
| 1.4 | 7 | 9.1 | 50 | 3 | 2.5 | 12.5 | 16.3 | 55 | 3 | |
| 1.45 | 7.3 | 9.4 | 50 | 3 | 2.55 | 12.8 | 16.6 | 55 | 3 | |
| 1.5 | 7.5 | 9.8 | 50 | 3 | 2.6 | 13 | 16.9 | 55 | 3 | |
| 1.55 | 7.8 | 10.1 | 50 | 3 | 2.65 | 13.3 | 17.2 | 55 | 3 | |
| 1.6 | 8 | 10.4 | 55 | 3 | 2.7 | 13.5 | 17.6 | 55 | 3 | |
| 1.65 | 8.3 | 10.7 | 55 | 3 | 2.75 | 13.8 | 17.9 | 55 | 3 | |
| 1.7 | 8.5 | 11.1 | 55 | 3 | 2.8 | 14 | 18.2 | 55 | 3 | |
| 1.75 | 8.8 | 11.4 | 55 | 3 | 2.85 | 14.3 | 18.5 | 55 | 3 | |
| 1.8 | 9 | 11.7 | 55 | 3 | 2.9 | 14.5 | 18.9 | 55 | 3 | |
| 1.85 | 9.3 | 12 | 55 | 3 | 2.95 | 14.8 | 19.2 | 55 | 3 | |
| 3 | 15 | 19.5 | 55 | 3 |
Recommendation for using the deep hole drills: drilling a pilot hole with HAM 30-1301
 |
Liquid Boost from nominal diameter 0.8 to 1.45 mm Advantages: – with the same pressure up to three times higher flow rate – higher tool life – more efficient chip removal |
We reserve the right to make technical changes. 