| 30-2181 | 30-2261 | 30-2341 | 30-2421 | 30-2501 | 30-2580 | 30-2660 | 30-2740 |
| 30-2221 | 30-2301 | 30-2381 | 30-2461 | 30-2541 | 30-2620 | 30-2700 |
 |
| HAM 30-2700 solid carbide deep hole drill 30 X D |
|
Engineering data
• special 4-facet ground • special point ground • special chip flute geometry • 15° RH helix • 4 guide chamfer |
 |
| Material |  |
 |
 |
 |
|||||||
| 30-2700 | very suitable | limited suitable | |||||||||
 cutting materialsolid carbide ultra micro grain |
 number of teeth - 2 |
 helix angle15° right hand fluted |
 HAM Standard |
 30 x Diameter |
 HAM Standard |
 Point angle 137° |
 Shank HA with IC |
 Special-polishing process |
 Interior Coolant |
 High Performance Cutting |
 Shrink Fit |
| Ø d1 (h7) mm |
l3 mm |
l2 mm |
l1 mm |
Ø d2 (h6) mm |
Ø d1 (h7) mm |
l3 mm |
l2 mm |
l1 mm |
Ø d2 (h6) mm |
|
| 2 | 60 | 64 | 110 | 4 | 6.5 | 195 | 208 | 250 | 8 | |
| 2.2 | 66 | 70.4 | 110 | 4 | 6.8 | 204 | 217.6 | 265 | 8 | |
| 2.3 | 69 | 73.6 | 110 | 4 | 7 | 210 | 224 | 265 | 8 | |
| 2.4 | 72 | 76.8 | 110 | 4 | 7.5 | 225 | 240 | 280 | 8 | |
| 2.5 | 75 | 80 | 115 | 4 | 7.8 | 234 | 249.6 | 315 | 8 | |
| 2.7 | 81 | 86.4 | 120 | 4 | 8 | 240 | 256 | 315 | 8 | |
| 2.8 | 84 | 89.6 | 125 | 4 | 8.5 | 255 | 272 | 315 | 10 | |
| 3 | 90 | 96 | 140 | 6 | 8.8 | 264 | 281.6 | 325 | 10 | |
| 3.2 | 96 | 102.4 | 150 | 6 | 9 | 270 | 288 | 335 | 10 | |
| 3.3 | 99 | 105.6 | 150 | 6 | 9.8 | 294 | 313.6 | 360 | 10 | |
| 3.5 | 105 | 112 | 155 | 6 | 10 | 300 | 320 | 365 | 10 | |
| 3.8 | 114 | 121.6 | 170 | 6 | 10.2 | 306 | 326.4 | 375 | 12 | |
| 4 | 120 | 128 | 170 | 6 | 10.8 | 324 | 345.6 | 395 | 12 | |
| 4.2 | 126 | 134.4 | 185 | 6 | 11.8 | 354 | 377.6 | 425 | 12 | |
| 4.5 | 135 | 144 | 185 | 6 | 12 | 360 | 384 | 430 | 12 | |
| 4.8 | 144 | 153.6 | 200 | 6 | ||||||
| 5 | 150 | 160 | 200 | 6 | ||||||
| 5.5 | 165 | 176 | 215 | 6 | ||||||
| 5.8 | 174 | 185.6 | 230 | 6 | ||||||
| 6 | 180 | 192 | 230 | 6 |
Recommendation for using the deep hole drills: drilling a pilot hole with HAM 30-1881 or HAM 30-1891
We reserve the right to make technical changes. 